Previous Topic Next Topic

Format Target Label Dialog

The Format Target Label dialog helps you to format the target labels on a gauge chart. It appears when you double-click a target label on a gauge chart, or right-click it and then select Format Target Label from the shortcut menu.

The dialog contains the following tabs: General, Font and Format.

OK

Applies the changes and closes the dialog.

Cancel

Does not retain any changes and closes the dialog.

Apply

Applies all changes and leaves the dialog open.

Help

Displays the help document about this feature.

General

Specifies the general properties of the labels.

Size

Specifies the size of the labels.

• Width
  Specifies the width of the labels, in pixels.
• Height
  Specifies the height of the labels, in pixels.
• X
  Specifies the horizontal coordinate of the top left corner of the labels, relative to their parent container.
• Y
  Specifies the vertical coordinate of the top left corner of the labels, relative to their parent container.
• Alignment
  Specifies the alignment of the label text.
• Word Wrap
  Specifies whether to enable the word wrap function for the label text.

Fill

Specifies the color and transparency of the labels.

• Fill
  Specifies the color to fill the labels.
• Transparency
  Specifies the transparency to fill the labels.

Border

Specifies the properties for borders of the labels.

• Border Type
  Displays the type of the border.
• Color
  Specifies the color of the border. To edit the color, select the color indicator and select a color from the color palette or input the hexadecimal value (for example, 0xff0000) of a color directly in the text box.
• Line Style
  Specifies the line style to apply to the border.
• Transparency
  Specifies the transparency for color of the border.
• Thickness
  Specifies the thickness of the border, in pixels.

• End Caps
  Specifies the ending style of the border line.

• butt
  Ends unclosed sub paths and dash segments with no added decoration.
• round
  Ends unclosed sub paths and dash segments with a round decoration that has a radius equal to half of the width of the pen.
• square
  Ends unclosed sub paths and dash segments with a square projection that extends beyond the end of the segment to a distance equal to half of the line width.
• Line Joint
  Specifies the line joint style for the border line.
  • miter
    Joins path segments by extending their outside edges until they meet.
  • round
    Joins path segments by rounding off the corner at a radius of half the line width.
  • bevel
    Joins path segments by connecting the outer corners of their wide outlines with a straight segment.
  • joint round
    Joins path segments by rounding off the corner at the specified radius.

• Path
  Specifies the fill pattern of the border line.

  • Outline Path
    Specifies the fill pattern of the border line to be outline path.
  • Fill Path
    Specifies the fill pattern of the border line to be whole path.
• Dash
  Specifies the dash size of border line.
  • Auto Adjust Dash
    If selected, the dash size will be adjusted automatically.
  • Fixed Dash Size
    If selected, the dash size will be fixed size.

Orientation

Specifies the orientation properties of the labels.

• Label Orientation
  Specifies the rotation angle of the labels.

Sample

Displays a preview sample of your selection.

Font

Specifies properties for font of the label text.

Font

Specifies the font format of text in the labels.

• Font list
  Lists all the available font faces that can be selected to apply to the text.
• Font Size
  Specifies the font size of the text.
• Font Color 
  Specifies the font color of the text.
• Transparency
  Specifies the color transparency of the text.
• Rotation
  Specifies the rotation angle of the text around its center, in degrees. The default value is 0.
• Shearing
  Specifies the gradient of the text.

Effects

Specifies the special effects of text in the labels.

• Style
  Specifies the font style of the text. It can be one of the following: plain, bold, italic, and bold italic.
• Strikethrough
  Specifies the style of the horizontal line with which the text is struck through. It can be one of the following: none, thin line, bold line, and double lines.
• Underline
  Specifies the style of the horizontal line under the text. It can be one of the following: none, single, single lower, bold line, bold lower, double lines, bold double, patterned line, and bold patterned.
• Superscript
  Raises the text above the baseline and changes the text to a smaller font size, if a smaller size is available.
• Embossed
  Makes the text appear to be raised off the page in relief.
• Outlined
  Displays the inner and outer borders of each character.
• Subscript
  Lowers the text below the baseline and changes the text to a smaller font size, if a smaller size is available.
• Engraved
  Makes the text appear to be imprinted or pressed into the page.
• Shadowed
  Adds a shadow beneath and to the right of the text.

Sample

Displays a preview sample of your selection.

Format

Specifies the data format of the labels.

Category

Lists the category types. Select one to customize its format.

Format

Displays all the formats of the selected category. Select the required one and select Add to add it as the format of the specified category. You can add only one format for each category.

Properties

Displays the properties of the format you select. If the formats listed in the Format box cannot meet your requirement, define the format in the text field and then select Add to add it as the format of the specified category.

Auto Scale in Number

Enabled when the target value is bound with a field that is of the Number data type. It specifies whether to automatically scale the target labels when the label values fall into the two ranges:

• When 1000 <= value < 10^15, the following quantity unit symbols of the International System of Units are used to scale the values: K (10^3), M (10^6), G (10^9), and T (10^12).
• When 0 < value < 0.001 or value >= 10^15, scientific notation is used to scale the values.

By default it is set to auto which means that the setting follows that of the chart. When it is true, the specified format applies to the integer part of the values after scaled, but if the specified format conflicts with Auto Scale in Number, for example the values are displayed in percentage, then the Auto Scale in Number setting is ignored.

Sample

Displays a preview sample of your selection.

Stack

Lists all the formats you select from different categories.

Add

Adds a format to the Stack list box.

Remove

Removes a format from the Stack list box.

Apply

Applies the specified format in the Stack list box to the labels.

Previous Topic Next Topic